Small practice. Bright discoveries.Explore the free starter collection
Back to worksheets
ScienceAges 7-9

Conductors, insulators & circuits

Compare conductors and insulators, series and parallel circuits, switches, fuses and circuit symbols. Review suitability for your learners before teaching.

New variationTry interactive challengeBrowse templates

Choose “Save as PDF” to keep a copy. Use your browser’s paper setting for A4 or Letter.

Worksheet StudioPractice pack · Ages 7-9

Conductors, insulators & circuits

Take your time. Show your thinking.

  1. 1. Which circuit instrument is connected IN PARALLEL across a component to measure the potential difference (voltage) in volts (V): a voltmeter or an ammeter?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  2. 2. What circuit component allows current to flow in ONE direction only (and emits light when it is an LED): a diode (or light-emitting diode) or a fixed resistor?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  3. 3. Which non-metal form of carbon (used in pencil leads) is an exception because it DOES conduct electricity: graphite or rubber?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  4. 4. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  5. 5. Materials such as plastic, rubber, glass and dry wood that do NOT allow electric current to flow through them are called: electrical insulators or electrical conductors?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  6. 6. Why are electrical wires made with a copper metal core on the inside and a flexible plastic coating on the outside: copper conducts the electricity while the plastic insulator prevents electric shocks and short circuits, or plastic conducts electricity?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  7. 7. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  8. 8. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  9. 9. What happens when you open (turn off) a switch in a simple series circuit: it creates a gap (open circuit) that stops the current flowing and turns the bulb off, or it makes the bulb brighter?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  10. 10. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  11. 11. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
  12. 12. For an electric current to flow and light up a bulb, what kind of path must the circuit form from one terminal of the battery to the other: a complete (closed) loop with no gaps, or a broken (open) loop?

    +−R
    Cell (+) ── Switch ── (−) · Closed Series Loop
12 questions · Seed 133 · Age guidance, not curriculum certification
View the answer key
Worksheet StudioAnswer key · Ages 7-9

Conductors, insulators & circuits

Answers and reasoning. Review before teaching.

  1. 1. Which circuit instrument is connected IN PARALLEL across a component to measure the potential difference (voltage) in volts (V): a voltmeter or an ammeter?

    Voltmeter

    A voltmeter has very high resistance and is connected across (in parallel with) a component.

  2. 2. What circuit component allows current to flow in ONE direction only (and emits light when it is an LED): a diode (or light-emitting diode) or a fixed resistor?

    Diode (or light-emitting diode)

    A diode has low resistance in the forward direction and very high resistance in reverse.

  3. 3. Which non-metal form of carbon (used in pencil leads) is an exception because it DOES conduct electricity: graphite or rubber?

    Graphite

    Graphite has delocalised electrons between its carbon layers, allowing it to conduct electricity.

  4. 4. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?

    Each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others

    In a parallel circuit, if one lamp fails or is switched off, current still flows through the other branches.

  5. 5. Materials such as plastic, rubber, glass and dry wood that do NOT allow electric current to flow through them are called: electrical insulators or electrical conductors?

    Electrical insulators

    Insulators have tightly bound electrons and block the flow of electric current.

  6. 6. Why are electrical wires made with a copper metal core on the inside and a flexible plastic coating on the outside: copper conducts the electricity while the plastic insulator prevents electric shocks and short circuits, or plastic conducts electricity?

    Copper conducts the electricity while the plastic insulator prevents electric shocks and short circuits

    The metal core carries current; the outer plastic sheath keeps users safe.

  7. 7. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?

    Their voltages cancel out and the bulb will not light

    Cells in series must be aligned positive-to-negative so their voltages add together.

  8. 8. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?

    The current is the SAME at every point in a series loop

    Charge is conserved—the same number of coulombs per second passes every point in a single loop; energy is transferred, not current used up.

  9. 9. What happens when you open (turn off) a switch in a simple series circuit: it creates a gap (open circuit) that stops the current flowing and turns the bulb off, or it makes the bulb brighter?

    It creates a gap (open circuit) that stops the current flowing and turns the bulb off

    A switch controls a circuit by safely opening or closing the conducting gap.

  10. 10. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?

    Light-dependent resistor (LDR)

    In bright light an LDR’s resistance falls; in darkness its resistance rises.

  11. 11. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?

    It goes out too because the single circuit loop is broken

    A break anywhere in a series loop stops current throughout the entire loop.

  12. 12. For an electric current to flow and light up a bulb, what kind of path must the circuit form from one terminal of the battery to the other: a complete (closed) loop with no gaps, or a broken (open) loop?

    A complete (closed) loop with no gaps

    Current only flows around a continuous, closed conducting pathway.

12 questions · Seed 133 · Age guidance, not curriculum certification