Compare conductors and insulators, series and parallel circuits, switches, fuses and circuit symbols. Review suitability for your learners before teaching.
Choose “Save as PDF” to keep a copy. Use your browser’s paper setting for A4 or Letter.
Worksheet StudioPractice pack · Ages 7-9
Conductors, insulators & circuits
Take your time. Show your thinking.
1. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?
Cell (+) ── Switch ── (−) · Closed Series Loop
2. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?
Cell (+) ── Switch ── (−) · Closed Series Loop
3. What safety device inside a plug or fusebox contains a thin wire designed to melt and break the circuit if the current becomes dangerously high: a fuse or a motor?
Cell (+) ── Switch ── (−) · Closed Series Loop
4. For an electric current to flow and light up a bulb, what kind of path must the circuit form from one terminal of the battery to the other: a complete (closed) loop with no gaps, or a broken (open) loop?
Cell (+) ── Switch ── (−) · Closed Series Loop
5. Which non-metal form of carbon (used in pencil leads) is an exception because it DOES conduct electricity: graphite or rubber?
Cell (+) ── Switch ── (−) · Closed Series Loop
6. In a parallel circuit, how does the total current leaving the battery compare to the currents in the individual parallel branches: the total current equals the sum of the currents in the branches, or the total current is zero?
Cell (+) ── Switch ── (−) · Closed Series Loop
7. In a standard circuit diagram, what component is represented by a circle with an “X” (cross) inside it: a filament lamp (bulb) or a battery?
Cell (+) ── Switch ── (−) · Closed Series Loop
8. What component has a resistance that changes significantly with temperature (used in digital thermometers and thermostats): a thermistor or a loudspeaker?
Cell (+) ── Switch ── (−) · Closed Series Loop
9. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?
Cell (+) ── Switch ── (−) · Closed Series Loop
10. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?
Cell (+) ── Switch ── (−) · Closed Series Loop
11. If you add a second cell in series (pointing in the same direction, + to −) to a circuit with a single bulb, what happens to the bulb: it shines more brightly because the voltage pushing the current has doubled, or it goes out?
Cell (+) ── Switch ── (−) · Closed Series Loop
12. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?
Cell (+) ── Switch ── (−) · Closed Series Loop
12 questions · Seed 105114 · Age guidance, not curriculum certification
Worksheet StudioPractice pack · Ages 7-9
Conductors, insulators & circuits
Take your time. Show your thinking.
1. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?
Cell (+) ── Switch ── (−) · Closed Series Loop
2. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?
Cell (+) ── Switch ── (−) · Closed Series Loop
3. What safety device inside a plug or fusebox contains a thin wire designed to melt and break the circuit if the current becomes dangerously high: a fuse or a motor?
Cell (+) ── Switch ── (−) · Closed Series Loop
4. For an electric current to flow and light up a bulb, what kind of path must the circuit form from one terminal of the battery to the other: a complete (closed) loop with no gaps, or a broken (open) loop?
Cell (+) ── Switch ── (−) · Closed Series Loop
5. Which non-metal form of carbon (used in pencil leads) is an exception because it DOES conduct electricity: graphite or rubber?
Cell (+) ── Switch ── (−) · Closed Series Loop
6. In a parallel circuit, how does the total current leaving the battery compare to the currents in the individual parallel branches: the total current equals the sum of the currents in the branches, or the total current is zero?
Cell (+) ── Switch ── (−) · Closed Series Loop
7. In a standard circuit diagram, what component is represented by a circle with an “X” (cross) inside it: a filament lamp (bulb) or a battery?
Cell (+) ── Switch ── (−) · Closed Series Loop
8. What component has a resistance that changes significantly with temperature (used in digital thermometers and thermostats): a thermistor or a loudspeaker?
Cell (+) ── Switch ── (−) · Closed Series Loop
9. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?
Cell (+) ── Switch ── (−) · Closed Series Loop
10. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?
Cell (+) ── Switch ── (−) · Closed Series Loop
11. If you add a second cell in series (pointing in the same direction, + to −) to a circuit with a single bulb, what happens to the bulb: it shines more brightly because the voltage pushing the current has doubled, or it goes out?
Cell (+) ── Switch ── (−) · Closed Series Loop
12. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?
Cell (+) ── Switch ── (−) · Closed Series Loop
12 questions · Seed 105114 · Age guidance, not curriculum certification
Worksheet StudioAnswer key · Ages 7-9
Conductors, insulators & circuits
Answers and reasoning. Review before teaching.
1. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?
It goes out too because the single circuit loop is broken
A break anywhere in a series loop stops current throughout the entire loop.
2. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?
The current is the SAME at every point in a series loop
Charge is conserved—the same number of coulombs per second passes every point in a single loop; energy is transferred, not current used up.
3. What safety device inside a plug or fusebox contains a thin wire designed to melt and break the circuit if the current becomes dangerously high: a fuse or a motor?
Fuse
If a fault causes excessive current, the fuse wire melts, cutting off the electricity to prevent overheating and fire.
4. For an electric current to flow and light up a bulb, what kind of path must the circuit form from one terminal of the battery to the other: a complete (closed) loop with no gaps, or a broken (open) loop?
A complete (closed) loop with no gaps
Current only flows around a continuous, closed conducting pathway.
5. Which non-metal form of carbon (used in pencil leads) is an exception because it DOES conduct electricity: graphite or rubber?
Graphite
Graphite has delocalised electrons between its carbon layers, allowing it to conduct electricity.
6. In a parallel circuit, how does the total current leaving the battery compare to the currents in the individual parallel branches: the total current equals the sum of the currents in the branches, or the total current is zero?
The total current equals the sum of the currents in the branches
By Kirchhoff’s current law (conservation of charge), current splits at a junction and recombines on return.
7. In a standard circuit diagram, what component is represented by a circle with an “X” (cross) inside it: a filament lamp (bulb) or a battery?
Filament lamp (bulb)
A circle containing a cross is the standard circuit symbol for an indicator or lighting lamp.
8. What component has a resistance that changes significantly with temperature (used in digital thermometers and thermostats): a thermistor or a loudspeaker?
Thermistor
A thermistor is a temperature-sensitive resistor.
9. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?
Their voltages cancel out and the bulb will not light
Cells in series must be aligned positive-to-negative so their voltages add together.
10. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?
Each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others
In a parallel circuit, if one lamp fails or is switched off, current still flows through the other branches.
11. If you add a second cell in series (pointing in the same direction, + to −) to a circuit with a single bulb, what happens to the bulb: it shines more brightly because the voltage pushing the current has doubled, or it goes out?
It shines more brightly because the voltage pushing the current has doubled
Two 1.5 V cells connected correctly in series supply 3.0 V, increasing the current through the bulb.
12. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?
Light-dependent resistor (LDR)
In bright light an LDR’s resistance falls; in darkness its resistance rises.
12 questions · Seed 105114 · Age guidance, not curriculum certification