Compare conductors and insulators, series and parallel circuits, switches, fuses and circuit symbols. Review suitability for your learners before teaching.
Choose “Save as PDF” to keep a copy. Use your browser’s paper setting for A4 or Letter.
Worksheet StudioPractice pack · Ages 10-12
Conductors, insulators & circuits
Take your time. Show your thinking.
1. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?
Cell (+) ── Switch ── (−) · Closed Series Loop
2. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?
Cell (+) ── Switch ── (−) · Closed Series Loop
3. In a standard circuit diagram, what does a long thin vertical line paired with a shorter, thicker vertical line represent: a single electrical cell, or an open switch?
Cell (+) ── Switch ── (−) · Closed Series Loop
4. In a simple SERIES circuit containing one battery and two bulbs, if you add a third identical bulb in the same single loop, what happens to the brightness of the bulbs: they become dimmer because the voltage is shared and total resistance increases, or they become three times brighter?
Cell (+) ── Switch ── (−) · Closed Series Loop
5. In a standard circuit diagram, what component is represented by a circle with an “X” (cross) inside it: a filament lamp (bulb) or a battery?
Cell (+) ── Switch ── (−) · Closed Series Loop
6. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?
Cell (+) ── Switch ── (−) · Closed Series Loop
7. What circuit component allows current to flow in ONE direction only (and emits light when it is an LED): a diode (or light-emitting diode) or a fixed resistor?
Cell (+) ── Switch ── (−) · Closed Series Loop
8. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?
Cell (+) ── Switch ── (−) · Closed Series Loop
9. Materials such as copper, aluminium, silver and steel that allow electric current to flow through them easily are called: electrical conductors or electrical insulators?
Cell (+) ── Switch ── (−) · Closed Series Loop
10. If you add a second cell in series (pointing in the same direction, + to −) to a circuit with a single bulb, what happens to the bulb: it shines more brightly because the voltage pushing the current has doubled, or it goes out?
Cell (+) ── Switch ── (−) · Closed Series Loop
11. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?
Cell (+) ── Switch ── (−) · Closed Series Loop
12. Materials such as plastic, rubber, glass and dry wood that do NOT allow electric current to flow through them are called: electrical insulators or electrical conductors?
Cell (+) ── Switch ── (−) · Closed Series Loop
12 questions · Seed 105139 · Age guidance, not curriculum certification
Worksheet StudioPractice pack · Ages 10-12
Conductors, insulators & circuits
Take your time. Show your thinking.
1. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?
Cell (+) ── Switch ── (−) · Closed Series Loop
2. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?
Cell (+) ── Switch ── (−) · Closed Series Loop
3. In a standard circuit diagram, what does a long thin vertical line paired with a shorter, thicker vertical line represent: a single electrical cell, or an open switch?
Cell (+) ── Switch ── (−) · Closed Series Loop
4. In a simple SERIES circuit containing one battery and two bulbs, if you add a third identical bulb in the same single loop, what happens to the brightness of the bulbs: they become dimmer because the voltage is shared and total resistance increases, or they become three times brighter?
Cell (+) ── Switch ── (−) · Closed Series Loop
5. In a standard circuit diagram, what component is represented by a circle with an “X” (cross) inside it: a filament lamp (bulb) or a battery?
Cell (+) ── Switch ── (−) · Closed Series Loop
6. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?
Cell (+) ── Switch ── (−) · Closed Series Loop
7. What circuit component allows current to flow in ONE direction only (and emits light when it is an LED): a diode (or light-emitting diode) or a fixed resistor?
Cell (+) ── Switch ── (−) · Closed Series Loop
8. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?
Cell (+) ── Switch ── (−) · Closed Series Loop
9. Materials such as copper, aluminium, silver and steel that allow electric current to flow through them easily are called: electrical conductors or electrical insulators?
Cell (+) ── Switch ── (−) · Closed Series Loop
10. If you add a second cell in series (pointing in the same direction, + to −) to a circuit with a single bulb, what happens to the bulb: it shines more brightly because the voltage pushing the current has doubled, or it goes out?
Cell (+) ── Switch ── (−) · Closed Series Loop
11. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?
Cell (+) ── Switch ── (−) · Closed Series Loop
12. Materials such as plastic, rubber, glass and dry wood that do NOT allow electric current to flow through them are called: electrical insulators or electrical conductors?
Cell (+) ── Switch ── (−) · Closed Series Loop
12 questions · Seed 105139 · Age guidance, not curriculum certification
Worksheet StudioAnswer key · Ages 10-12
Conductors, insulators & circuits
Answers and reasoning. Review before teaching.
1. Why are the lights and sockets in a home wired in PARALLEL rather than in series: each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others, or parallel uses no wire?
Each light is on its own branch so it receives full voltage and can be switched on or off independently without turning off the others
In a parallel circuit, if one lamp fails or is switched off, current still flows through the other branches.
2. In a simple SERIES circuit with two bulbs in a single loop, if one bulb’s filament breaks (blows), what happens to the other bulb: it goes out too because the single circuit loop is broken, or it stays lit?
It goes out too because the single circuit loop is broken
A break anywhere in a series loop stops current throughout the entire loop.
3. In a standard circuit diagram, what does a long thin vertical line paired with a shorter, thicker vertical line represent: a single electrical cell, or an open switch?
Single electrical cell
The long line marks the positive (+) terminal and the short thick line marks the negative (−) terminal of a cell.
4. In a simple SERIES circuit containing one battery and two bulbs, if you add a third identical bulb in the same single loop, what happens to the brightness of the bulbs: they become dimmer because the voltage is shared and total resistance increases, or they become three times brighter?
They become dimmer because the voltage is shared and total resistance increases
In a series loop, adding more bulbs increases resistance and splits the battery voltage across more components.
5. In a standard circuit diagram, what component is represented by a circle with an “X” (cross) inside it: a filament lamp (bulb) or a battery?
Filament lamp (bulb)
A circle containing a cross is the standard circuit symbol for an indicator or lighting lamp.
6. What happens if two identical cells in a torch are put in facing opposite directions (+ touching +): their voltages cancel out and the bulb will not light, or the bulb shines twice as bright?
Their voltages cancel out and the bulb will not light
Cells in series must be aligned positive-to-negative so their voltages add together.
7. What circuit component allows current to flow in ONE direction only (and emits light when it is an LED): a diode (or light-emitting diode) or a fixed resistor?
Diode (or light-emitting diode)
A diode has low resistance in the forward direction and very high resistance in reverse.
8. In a series circuit, how does the electric current measured at different points around the single loop compare: the current is the SAME at every point in a series loop, or it gets used up by the bulb?
The current is the SAME at every point in a series loop
Charge is conserved—the same number of coulombs per second passes every point in a single loop; energy is transferred, not current used up.
9. Materials such as copper, aluminium, silver and steel that allow electric current to flow through them easily are called: electrical conductors or electrical insulators?
Electrical conductors
Metals have free-moving (delocalised) electrons that conduct electric current readily.
10. If you add a second cell in series (pointing in the same direction, + to −) to a circuit with a single bulb, what happens to the bulb: it shines more brightly because the voltage pushing the current has doubled, or it goes out?
It shines more brightly because the voltage pushing the current has doubled
Two 1.5 V cells connected correctly in series supply 3.0 V, increasing the current through the bulb.
11. What component has a resistance that decreases when brighter light shines on it (used in automatic street lights): a light-dependent resistor (LDR) or a thermistor?
Light-dependent resistor (LDR)
In bright light an LDR’s resistance falls; in darkness its resistance rises.
12. Materials such as plastic, rubber, glass and dry wood that do NOT allow electric current to flow through them are called: electrical insulators or electrical conductors?
Electrical insulators
Insulators have tightly bound electrons and block the flow of electric current.
12 questions · Seed 105139 · Age guidance, not curriculum certification